What is IU Paging Success Ratio?

IU Paging Success Ratio defied for Huawei system.

This KPI can be used to evaluate the successful paging responses to the pagings from the Core Network (CN) in one RNC.

The Attempt Paging Procedure starts when the CN sends a PAGING message to the RNC, and finishes when the UE in idle mode receives the PAGING TYPE 1 message from the RNC.

The Successful Paging Procedure finishes when the RNC receives an RRC CONNECTION REQUEST from the UE in idle mode.

 

IU Paging Success Ratio =
(VS.RANAP.Paging.Succ.IdleUE/ VS.RANAP.Paging.Att.IdleUE)*100%

 

HSDPA Frame Loss

These counters relating to frame loss are available on the RBS to monitor HighSpeed data service in the downlink direction.

IubDataStreams::pmHsDataFramesLostSpiXX
- the number of HSdata frames lost, destroyed and errored over Iub in the RBS. There areseparate counters for each of the priority classes.

IubDataStreams::pmHsDataFramesReceivedSpiXX
- the totalnumber of HS data frames correctly received over Iub in the RBS. Thereare separate counters for each of the priority classes.

The XX suffix represents the priority class and can range from 00 to 15.The counters can be used to indicate data loss rate for the HS service.High frame loss will indicate potential congestion problems. RecommendedPerformance Indicator for this is:



Frame Loss Rate on the path from SRNC to RBS

Find more HSDPA Counters at www.telecomfunda.com/forum

UE Measurements

Intra-frequency measurements: measurements on downlink physical channels at the same frequency as the active set. A measurement object corresponds to one cell.

Inter-frequency measurements: measurements on downlink physical channels at frequencies that differ from the frequency of the active set. A measurement object corresponds to one cell.

Inter-RAT measurements: measurements on downlink physical channels belonging to another radio access technology than UTRAN, e.g. GSM. A measurement object corresponds to one cell.

Traffic volume measurements: measurements on uplink traffic volume. A measurement object corresponds to one cell.

Quality measurements: Measurements of downlink quality parameters, e.g. downlink transport block error rate. A measurement object corresponds to one transport channel in case of BLER. A measurement object corresponds to one timeslot in case of SIR (TDD only).

UE-internal measurements: Measurements of UE transmission power and UE received signal level.

UE positioning measurements: Measurements of UE position.The UE supports a number of measurements running in parallel. The UE also supports that each measurement is controlled and reported independently of every other measurement.

Pilot Channel failure - High Downlink Interference

Symptoms:

From the drive test, following symptoms will be observed by using TEMS:

• Received Ec/No of the pilot channel is less than –16dB and

• Received RSCP of the pilot channel is high enough to maintain the connection,e.g. >-   100dBm and

• DL RSSI is very high and

• The connection finally drops.

Good Excel Sheet on CPICH Calculator

How can I find RRU Type in Ericsson NodeB?

There are several ways to Find RRU type in Node B.

For Ericsson System connect through MOSHELL and

Enter command cabx you can find the RRU type.

Also enter INVH Command for RRU and DUW type.

If You Know More Ways to Know than Discuss Here

CPICH Optimization

Good Document on CPICH Optimization from Maxis

CPICH Optimization

You can view Document Here

Content

• Objective
• Technical Background
• Deployment Area
• Performance Results
• Traffic Results
• Capacity Results
• Summary

Download Full Document in PDF from Here

Deployment of CPICH optimization is driven by:
–Improving current 3G coverage and increase 3G traffic
–Improve in-building penetration for 3G
–Reduce IRAT HO to 2G
–Offload traffic from 2G layer

How Can We Avoide IRAT Handover?
Traffic Shift Strategy for 3G to 2G

What are the conditions you typically set to trigger IRAT handover?

RSCP and Ec/Io are used to trigger IRAT handover:

1.       RSCP ≤ -100dBm.

2.       Ec/Io ≤ -16dBm.

Find more document on IRAT
WCDMA IRAT Handover
Details on IRAT Parameter Optimization Document

How many channelization codes are available?

The number of channelization codes available is dependent on the length of code.  In the uplink the length is defined as between 4 and 256.  In the downlink the length is defined as between 4 and 512.

Know more about Scrambling Code

UMTS Scrambling Code Planning Guide

What is channelization code?

Channelization codes are orthogonal codes used to spread the signal and hence provides channel separation, that is, channelization codes are used to separate channels from a cell.

To Know more on WCDMA

100 WCDMA Documents

LTE Presetations 

How much is your HSDPA (max) link power?

HSDPA link power is typically 4 to 5dB below the maximum NodeB maximum output power.  For example, for 43dBm maximum NodeB power the HSDPA link power is 39dBm.

HSDPA Network Planning Guide

What is Difference between ARQ and HARQ?

HSDPA Measurement Events